项目名称：河南银基?冰雪世界主题乐园夜景照明工程

　　此项目为2021阿拉丁神灯奖工程类参评项目

　　申报单位：北京光影国际照明设计

　　项目地址：河南省新密市银基国际旅游度假区

　　设计单位：北京光影国际照明设计

　　施工单位：泛光照明工程有限公司

　　业主单位：河南银基轩辕圣境文化旅游有限公司

　　项目简介

　　本项目是一个专为3-12岁孩子打造集冰场、娱雪、游乐项目为一体的综合性室内冰雪主题乐园。总面积26000 ㎡ ，拥有圣诞世界、白色城堡、雪猫小镇、翡翠谷四大特色区，为室内、外多重体验的娱乐项目，是国内第一个以冰雪娱乐为主的综合性室内乐园；
项目概括：
建筑面积26000㎡ 用地60亩
3000㎡奇幻冰湖 360m绚丽冰路
8大游玩设备 4大主题场景
总投资5亿 亚洲少有的集冰场、娱雪、游乐项目为一体的四季运营的综合性室内冰雪主题乐园
This project is a comprehensive indoor ice and snow theme park designed for children aged 3-12, which integrates ice rink, snow entertainment and amusement projects. With a total area of 26,000 square meters, it has four acteristic areas: Christmas World, White Castle, Snow Cat Town and Emerald Valley. It is an indoor and outdoor multi-experience entertainment project, and it is the first comprehensive indoor park based on snow and ice entertainment in China.

项目宣传视频：

　　照明技术指标

　　明装下照筒灯：20W~50W 色温3000K 数量600套
染色下照筒灯：36W 色温RGBW 100套
线形洗墙灯：功率20W/m 色温RGB 数量300米
演绎灯串：功率5W/m 色温RGB 数量2600米
投影互动灯具：功率500W 色温RGB 数量36套
跑马灯：功率5W 色温RGB 数量107套
弯挂壁灯：功率10W 色温2700K 数量48套
LED支架灯：功率12W/m 色温2700K 数量170米
投光灯：功率8W 色温3000K 数量58套
埋地上照灯：功率90W 色温3000K 数量32套
LED柔性霓虹灯管：功率6W/m 色温RGB 数量370米

供配电系统
1．本工程为220/380V供配电系统，采用放射式供电方式；
2．计量：夜景照明配电系统均在上级配电箱（柜）进行计量；
导线选择和线路敷设
所有供配电线路和控制线路必须按设计规范要求穿厚壁热镀锌钢管或金属线槽敷设，任何地方都不能出现裸导线的情况，更不能把供电线路直接埋在地面和墙体内；
2. 照明线路采用WDZB-YJY-1.0KV铜芯无卤低烟B级阻燃交联聚乙烯绝缘电力电缆；低压线路采用ZR-RVV阻燃铜芯电缆；
3. 电缆分支或有破开处须设防水接线盒并离地0.3m安装；敷设管线应在适当位置加拉线盒（直线：30m，一个弯：20m，二个弯：15m，三个弯：8m）；4.管线埋地敷设时埋地深度不小于0.7m，在寒冷地区电缆宜埋设于冻土层以下；所有穿过建筑物伸缩缝、沉降缝、后浇带的管线应按《建筑电气安装工程图集》中有关作法施工；
设备要求：
1）照明设备所有带电部分应采用绝缘、遮拦或外护物保护，距地面2.8m以下的照明设备应使用工具才能打开外壳进行光源维护；
2）室外安装照明配电箱与控制箱等应采用防水、防尘型，防护等级不应低于IP54；
3）室外配电箱内元器件应考虑室外环境温度、湿度的影响，距地面2.8m以下的电气设备应借助于钥匙或工具才能开启；
4）LED灯具应选用专用开关电源，LED灯具输入电压应与开关电源输出电压一致；
5）在正常视角范围内的光源可直视灯具，必须采取有效防眩光措施；
6）对人员可触及的照明设备，当表面高于60℃时，必须采用隔离保护措施；
7）灯具、附件及电气设备满足项目所在地气候环境条件下正常工作；
8）夜景照明灯具防护等级必须满足消防安全要求；室外雨棚嵌入式筒灯防护等级不低于IP44,水下灯防护等级不低于IP68等；
9)所有I类灯具均设置地线接地保护;
10)灯具功率因数不应低于0.9，以减少线路损失，确保供电质量及光源效率.
时间控制器系统要求：
1）开、关时间任意可调；
2） 已调好的开、关时间不受停电影响，自动记忆；
3）每天可做十次开、关动作，开、关时间一周内可任意编程；
4）可自动，也可手动控制，设有自动保护装置；
5）内消耗功率低；
施工安装要求：
1）夜景照明灯具及配套电器、开关电源、控制器等电气设备禁止安装在可燃材料表面；
2）开关电源、各种控制器必须按照施工设计规范要求安装在金属外壳的箱体内，不得埋在地面和墙体内；
3）灯具的电缆电线接头应端子连接或涮锡连接、并做防水处理；
4）为了保证安装强度和防止雨水腐蚀，灯具安装支架、固定螺丝应全部为不锈钢或铝合金材质；
5）灯具、管线及电气设备布置不得影响消防安全疏散与救援；
6）室外灯具外壳颜色应与安装部位表面颜色协调；外立面夜景照明灯具及布线应做到不外露、不易触碰到，主立面严禁外露；
7）所有供配电线路和控制线路必须按设计规范要求穿厚壁热镀锌钢管或金属线槽敷设，任何地方都不能出现裸导线的地方，亦不可直埋于地面或者墙体内；
8）施工满足项目所在地的地方标准及施工规范要求；
Lighting down light: 20W~50W color temperature 3000K number of 600 sets

Dyeing down light: 36W color temperature RGBW 100 sets

Linear wall washing lamp: power 20W/m color temperature RGB quantity 300m

Deductive lamp string: power 5W/m color temperature RGB quantity 2600 meters

Projection interactive lamps: power 500W color temperature RGB quantity 36 sets

Running lamp: power 5W color temperature RGB number 107 sets

Curved hanging wall lamp: power 10W color temperature 2700K quantity 48 sets

LED bracket light: power 12W/m color temperature 2700K quantity 170 meters

Projection lamp: power 8W, color temperature 3000K, quantity 58 sets

Buried light: power 90W color temperature 3000K Quantity 32 sets

LED flexible neon tube: power 6W/m color temperature RGB quantity 370 meters



Power supply system

1. This project is 220/380V power supply and distribution system, using radiation power supply mode;

2. Metering: Nightview lighting distribution system are measured in the superior distribution box (cabinet);

Conductor ion and circuit laying

All power supply and distribution lines and control lines must be laid through thick wall hot dip galvanized steel pipe or metal trough according to the requirements of the design specification. Bare wires can not appear anywhere, let alone the power supply lines directly buried in the ground and walls;

2. The lighting line adopts WDZB-YJY-1.0kV copper core halogen-free low-smoke B-grade flame retardant XLPE insulated power cable; ZR-RVV flame retardant copper core cable for low voltage line;

3. Water proof junction box shall be set up at cable branch or broken place and shall be installed 0.3m above the ground; The pipeline should be laid in the appropriate position of the wire box (straight line: 30m, one bend: 20m, two bend: 15m, three bend: 8m); 4. The buried depth of the pipeline should not be less than 0.7m when it is laid in ground. In cold areas, the cable should be buried under the permafrost; All the pipelines through the expansion joints, settlement joints and post-cast belts of the building shall be constructed according to the relevant practices in the Atlas of Building Electrical Installation Engineering;

Equipment requirements:

1) All live parts of the lighting equipment should be protected by insulation, shielding or external protection. The lighting equipment below 2.8m the ground should use tools to open the shell for light source maintenance;

2) Outdoor lighting distribution box and control box should be waterproof and dustproof, and the protection grade should not be lower than IP54;

3) The components in the outdoor distribution box should consider the influence of outdoor environment temperature and huity, and the electrical equipment below 2.8m the ground should be opened with the help of keys or tools;

4) LED lamps should use special switching power supply, and the input voltage of LED lamps should be consistent with the output voltage of the switching power supply;

5) The light source within the normal viewing Angle can look directly at the lamp, and effective anti-glare measures must be taken;

6) For lighting equipment accessible to personnel, when the surface is higher than 60℃, isolation protection measures must be adopted;

7) The lamps, accessories and electrical equipment should work normally under the climatic and environmental conditions of the project location;

8) The protection level of nightview lighting fixtures must meet the fire safety requirements; The protection level of outdoor canopy embedded downlight should not be lower than IP44, and the protection level of underwater light should not be lower than IP68;

9) All Class I lamps are equipped with ground wire grounding protection;

10) The power factor of the lamp should not be less than 0.9 to reduce the line loss and ensure the quality of power supply and the efficiency of the light source.

Time controller system requirements:

1) Opening and closing time can be adjusted;

2) The adjusted on and off time is not affected by power failure, and it can be automatically remembered;

3) Can do 10 times a day on and off action, on and off time within a week can be arbitrary programming;

4) It can be controlled automatically or manually, and equipped with automatic protection device;

5) Low internal power consumption;

Construction and installation requirements:

1) Nightview lighting lamps and supporting electrical appliances, switching power supply, controllers and other electrical equipment are prohibited to be installed on the surface of combustible materials;

2) Switching power supply and various controllers must be installed in the box of the metal shell in accordance with the requirements of the construction design specification, and shall not be buried in the ground and wall;

3) The cable and wire connectors of lamps and lanterns should be connected with terminals or dipping tin, and waterproof treatment;

4) In order to ensure the installation strength and prevent rain corrosion, the mounting bracket and fixing screws of the lamp should be made of stainless steel or aluminum alloy;

5) Layout of lamps, pipelines and electrical equipment shall not affect fire safety evacuation and rescue;

6) The exterior lamp shell color should be in harmony with the surface color of the installation part; External facade night lighting lamps and wiring should be not exposed, not easy to touch, the main facade is strictly prohibited exposure;

7) All power supply and distribution lines and control lines must be laid through thick-walled hot-dip galvanized steel pipes or metal grooves according to the requirements of the design specifications. No bare wires can be found anywhere, nor can they be directly buried in the ground or walls;

8) The construction shall meet the local standards and construction specifications of the project site;

　　节能措施及效果

　　本案依据各独立开放的园区及运营游览路线，时钟自动切换，在一天中的各时间段随游客的数量将其引流，智能化、人性化的灯光成为辅助运营的最有利的方式之一，年用电荷载完全满足国家及地方的相关标准。

In this case, according to the independent and open parks and operating tour routes, the clock automatically switches, and the number of tourists in each time period of the day will be drainage, intelligent and humanized lighting has become one of the most favorable ways to assist the operation, and the annual electricity load fully meets the relevant national and local standards.

　　照明设计创新点

　　本项目作为国内第一个以冰雪娱乐为主的综合性室内乐园，灯光打造了一场超脱现实、无比梦幻的沉浸体验，自开业之日起就得到了业内人士及广大游客的极大关注。
除此之外，冰湖区域灯具的控制方式采用了当时最先进的蓝牙传输方式，模式切换操作性较网络控制，更加流畅、快捷。

As the first comprehensive indoor park mainly focused on ice and snow entertainment in China, the lighting has created an immersive experience beyond reality and unparalleled dreams. Since its opening, the project has attracted great attention the industry and tourists.

In addition, the control mode of the lamps in the frozen lake area adopts the most advanced Bluetooth transmission mode at that time, and the mode switching operation is smoother and faster than network control.

　　项目实际运行评价

　　设 计 访 谈
尊敬的领导：
您好，很荣幸被邀请参与贵司“河南银基冰雪世界主题乐园”的灯光设计工作，时至今日，项目已顺利投入使用，我们很期待聆听运营管理及设计师们，灯光在实际运行中的评价及指导意见，以便我们更加竭诚的为您服务，期待与您的下次合作。
Q1、开业后运营情况是怎样的？
答： 项目2017年12月开业，迄今为止，不论是游客量还是各项经营指标都超出了甲方预设目标，由于游客量过大，为了保证游客体验度，运营方不得不采取各种限制客流措施。
Q2、本室内乐园在国内、周边有什么影响与意义？
答：本项目作为国内第一个以冰雪娱乐为主的综合性室内乐园，自开业之日起就得到了业内人士及游客的极大关注。本项目的建成开业填补了中原市场的空白，为周边市民提供了差异化的旅游产品体验，从游客的构成上看，有一半是来自郑州以外的周边城市和周边省份。
Q3、灯光设计公司及呈现的最终效果如何？
答：作为一个室内乐园，灯光在氛围营造上起到了核心作用。光影国际帮助我们打造了一场超脱现实、无比梦幻的沉浸体验。除此之外，我们在运营中有不间断的各式表演，灯光在其中扮演着重要的角色，带动整体的氛围，激发引导游人的兴奋心情，把整个氛围推向高潮。
Q4、开业后，灯光是如何辅助运营及效果呈现的？在使用中，实际节能效果如何？
答：开业后，美轮美奂的灯光为整个银基冰雪世界的氛围烘托起到了很好的作用，泛光结合演出灯光将整个冰雪世界打造成一个一年四季飘雪的梦幻乐园。由于游客量过大，运营方不得不采取各种限制客流措施，在游览动线上，舞台效果类灯光配合音响设备，对游客的引流确实可以起到很大作用。节能方面，设计单位采用的全部LED型光源的灯具，以及先进的智能系统，我们在实际使用中调节方便，受益颇多，完全契合于国家节能减排的目标和总体要求。

　　申报单位

　　公司成立十年以来，由郑志伟先生领衔二十余位顶尖团队，致力于光环境设计与研究。以国际视野和世界领先的灯光技术方案，创造极具视觉艺术及商业价值的光影作品。
专注于城市地标、商业综合体、星级酒店、文旅小镇、城市景观等全球精品项目灯光设计，光影国际是万达、恒大、泰禾、佳兆业等众多地产的优秀合作伙伴，设计了如青岛2008迎奥城市夜景、重庆江北区城市夜景、天津万达中心、北京合生汇、成都银泰城、恒大海花岛、广州融创主题乐园、深圳佳兆业国际主题乐园等众多国内知名项目。光影国际参与并制定了万达室内乐园基础照明设计标准、万达A-02，B02，B03，B-02，B-04BIM标准、光之变革美术馆篇照明质量评估方法与体系研究、博物馆照明设计标准等。作品屡获国际、国内众多大奖，致力于打造中国第一灯光设计品牌。

Since the establishment of the company ten years ago, Mr. Zheng Zhiwei led more than 20 top team, committed to the light environment design and research. With the international vision and the worlds leading lighting technology solutions, to create great visual art and commercial value of light and shadow works.

Focused on the city landmarks, commercial complexes, star hotel, tour town, urban landscape, such as global high-quality goods project lighting design, lighting, Evergrande, taihe, wanda international is jia zhaoye numerous excellent partner of real estate, such as design such as Qingdao 2008 to meet the urban night scene, night at chongqing jiangbei city, tianjin wanda center, Beijing, chengdu Yintai connation remit city, constant melting sea island, guangzhou a theme park, shenzhen jia zhaoye international theme park, and many other famous domestic projects. Lighting International participated in and formulated basic lighting design standards for Wanda Indoor Park, Wanda A-02, B02, B03, B-02, B-04BIM standards, research on lighting quality evaluation methods and systems for the Light Revolution Museum, and lighting design standards for museums, etc. Works have won many international and domestic awards, is committed to building Chinas first lighting design brand.